[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[no subject]
- <!--x-content-type: text/plain -->
- <!--x-date: Sun, 18 Dec 2005 20:58:36 -0800 (PST) -->
- <!--x-from-r13: wvzcbc ng lnubb.pbz (Xvz Bbcbivgpu) -->
- <!--x-message-id: [email protected] -->
- <!--x-reference: [email protected] --> "http://www.w3.org/TR/html4/loose.dtd">
- <!--x-subject: [ale] OT: question about replacing batteries in a APC UPS -->
- <li><em>date</em>: Sun, 18 Dec 2005 20:58:36 -0800 (PST)</li>
- <li><em>from</em>: jimpop at yahoo.com (Jim Popovitch)</li>
- <li><em>in-reply-to</em>: <<a href="msg00251.html">[email protected]</a>></li>
- <li><em>subject</em>: [ale] OT: question about replacing batteries in a APC UPS</li>
I suspect that the 12amp hour batteries might work in the 700 model, HOWEVER you really should check with APC Support to see.
-Jim P.
----- Original Message ----
From: Van Loggins <vanloggins at gmail.com>
To: ale at ale.org
To: Atlanta Linux Enthusiasts <ale at ale.org>
Sent: Sunday, December 18, 2005 9:18:13 PM
Subject: [ale] OT: question about replacing batteries in a APC UPS
My current UPS which is a APC Smart-UPS 1000. It started intermittantly
beeping a while back and after reading the online manual from APC
I determined that the beeps were because the batteries were dying and
that I needed to replace them. I found replacement batteries for it
on ebay and bought them.
To make a long story short, this didn't fix the problem, in fact it got
worse. The unit started beeping nonstop and would shut itself off and
then wait for a minute or so and turn itself back on only to start
beeping again, and the unit doesn't keep running if the power is pulled
even though the charge meter is at 100% for the batteries.
I'm no expert but I think this means that the the unit is pretty well
shot, and now I am stuck with two "Brand New" 12 volt 12 amp hour gel
lead acid batteries. I am looking at a APC Smart-UPS 700
that I have the chance to get, but it needs batteries and after checking
into it, I found out that this model needs 12 volt 7 amp hour gel lead
acid batteries.
My question is this, would I be able to use the new batteries that I
just bought for my now defunct APC Smart-UPS 1000 in the APC Smart-UPS
700 that I'm looking at buying?
in summary the old unit I had uses 12 volt 12 amp hour batteries, and
the replacement unit I am looking at uses 12 volt 7 amp hour batteries.
They look to be approximately the same size and hook up the same way.
Thanks for any info that you guys can pass along.
Merry Christmas to everyone!!!
Van
_______________________________________________
Ale mailing list
Ale at ale.org
<a rel="nofollow" href="http://www.ale.org/mailman/listinfo/ale">http://www.ale.org/mailman/listinfo/ale</a>
</pre>
<!--X-Body-of-Message-End-->
<!--X-MsgBody-End-->
<!--X-Follow-Ups-->
<hr>
<!--X-Follow-Ups-End-->
<!--X-References-->
<ul><li><strong>References</strong>:
<ul>
<li><strong><a name="00251" href="msg00251.html">[ale] OT: question about replacing batteries in a APC UPS</a></strong>
<ul><li><em>From:</em> vanloggins at gmail.com (Van Loggins)</li></ul></li>
</ul></li></ul>
<!--X-References-End-->
<!--X-BotPNI-->
<ul>
<li>Prev by Date:
<strong><a href="msg00252.html">[ale] SuSE update</a></strong>
</li>
<li>Next by Date:
<strong><a href="msg00254.html">[ale] changes to ftp.ale.org</a></strong>
</li>
<li>Previous by thread:
<strong><a href="msg00251.html">[ale] OT: question about replacing batteries in a APC UPS</a></strong>
</li>
<li>Next by thread:
<strong><a href="msg00256.html">[ale] OT: question about replacing batteries in a APC UPS</a></strong>
</li>
<li>Index(es):
<ul>
<li><a href="maillist.html#00253"><strong>Date</strong></a></li>
<li><a href="threads.html#00253"><strong>Thread</strong></a></li>
</ul>
</li>
</ul>
<!--X-BotPNI-End-->
<!--X-User-Footer-->
<!--X-User-Footer-End-->
</body>
</html>